Repair of the pressing plunger of the press D6248 (us.6300 tons) – located on the territory of LLC "DKG" (Chelyabinsk) See the TOR and related documentation (Complex service)
OKPD2 category:
Show all (0 more)
28.41.33.130 Прессы гидравлические
28.41.33.190 Прессы для обработки металлов, не включенные в другие группировки
Not applicable. Proposal shall cover the entire lot.
Restriction on submission of a bid higher than previously submitted
Bidding initiator has set a restriction on submission of a bid with a price which is higher than the price of the previous bid submitted by the bidder. Once the bid is submitted, the stated price can not be increased.
:
Yes
Upload of bid-related documents required
Bids not supported with documentation will not be considered.
:
Yes
Auto-extension
If within the last 30 minutes of bid submission period a new bid is submitted, then bid submission deadline will automatically be extended by 30 minutes from the time the last bid is submitted.
:
30 minutes
Payment terms:
The contractor indicates in his commercial offer the cost, terms and payment options.
Delivery terms:
1. Application of JSC "EPM-NEZ", Novo Cherkassk
2. Place of manufacture:
The territory of the Contractor.
3.The purpose of manufacturing:
Elimination of defects on the surface of the pressing plunger to create a durable seal operation. 4. Term of work completion
4.1. The beginning of the work is June 2021
. 4.2. The contractor specifies the completion date in the commercial offer.
5. Brief technical description:
The repaired plunger is supported by a bronze support sleeve and a bronze pressure sleeve, where a chevron seal is located between them.
6. List and scope of work performed.
6.1 Repair (process) the surface of the pressing plunger with a diameter of 1300 mm and a length of 4590 mm, ensuring the same diameter and surface cleanliness according to drawing 28-402. Currently, there is corrosion on the surface in the form of rust. The contractor himself makes a decision on the method of surface treatment. The existing diameters of the pressing plunger along the length (from left to right according to the drawing) are the beginning of 1299.896 mm. the middle is 1299.832 mm. The end is 1299.67
6.2. After repair according to p 6.1, measure the hardness of the treated surface of the pressing plunger and compare with the data of drawing 28-402. When removing the hardened layer, the surface should be subjected to surface hardening according to the drawing.
6.3 After repair according to p6.1 and p.6.2, measure the actually obtained diameter of the pressing plunger for the manufacture of repair bronze support and pressure bushings.
7. Supply of materials, equipment, tools to perform this work.
7.1. Materials, equipment and components are supplied by the Contractor.
7.2 Delivery of the pressing plunger for repair to the contractor and removal of the repaired one is carried out by agreement.
7.3 The Customer recommends that the contractor visit the site where the pressing plunger is located to determine the exact amount of surface repair work.
8. The requirement for the TAP:
The Contractor in his commercial offer specifies the deadlines, cost, payment options for work and other conditions.
9. Acceptance of the Product is carried out on the territory of the Contractor with the signing of the Acceptance Certificate.
10. The Contractor provides the Customer with a warranty for the product for at least 12 months from the date of commissioning.
11. Requirements for the Contractor
11.1. The Contractor must have the necessary production and human resources to perform this work
11.2. After completion of the work, the contractor transfers to the customer all certificates for the materials used during the repair of the product, the actual diameter of the pressing plunger and its hardness after heat treatment according to drawing 28-402
11.3. The Contractor provides a guarantee for the products manufactured by him for at least 12 months.
11.4. Employees involved in the performance of work must have professional training appropriate to the nature of the work.
.
Georeferencing:
Rostov region, Novocherkassk, Aluminum platform
Comments: The participant who took part in the procedure (made an offer), before the deadline for accepting applications, is obliged to upload the following documents to the system:
1. The Charter (with all additions and changes, if any).
2. Certificate of state registration.
3. Certificate of tax registration.
4. Extract from the Unified State Register of Legal Entities.
5. Balance sheet as of the last reporting date with a mark of the tax authority on acceptance.
6. Documents confirming the representative's authority to sign documents:
— Decision (Protocol).
— Power of attorney.
7. Job offer (see the file "Job Offer")
8. Contact person: Oleg Mikhailovich Martyshchenko - Chief Mechanic. Tel. 8 (8635)29-48-24, fax 8 (8635)29-42-55, e-mail: OMartischenko@energoprom.ru
9. Certificate of compliance with the requirements of ISO 9001:2008 (if available)
This request is not a notice of a tender or auction and does not give any rights to participants, does not entail any obligations other than those expressly specified in the notification.
10. Prior to registration of the work permit, the Contractor is obliged to provide the Customer with the following documents:
- a copy of the certificate (SRO) for the right to perform this type of work;
- copies of documents confirming the presence of a labor protection service and/or a labor protection specialist in the contractor (an order of appointment to a position in the contractor, a certificate of a labor protection specialist) or the existence of an agreement with an accredited organization in the field of labor protection services;
- a copy of the instruction on labor protection from the instruction log;
- POR or PPR or RTI;
- a copy of the protocol of certification of workers on labor protection;
- copies of certificates of certification of ITR on labor protection and on general requirements of industrial safety. When performing work on gas, on pressure vessels, using GPM, in electrical installations, fire works – copies of certificates for each type of work;
- medical admission of personnel;
- copies of certificates of gas and electric welders, slingers, crane operators, lifts (towers). For gas and electric welders, copies of the PTM certification protocols.
In case of detection of inconsistencies of the information in the submitted documents with the requirements of regulatory legal acts, the Customer has the right to initiate an audit by the Health and Safety Service in matters of Occupational Safety and Industrial Safety in the Contractor's organization.
Venue of bidding:
This call for bids is held in electronic form on the e-marketplace of B2B-Center group (www.b2b-center.ru). Bids shall be submitted in the form of e-document.
Контактное лицо:
Мартыщенко Олег Михайлович - Главный механик
Тел. 8 (8635)29-48-24,
e-mail: OMartischenko@energoprom.ru
