Modification of mouthpieces 450 mm, 500 mm, 555 mm, 610 mm, 650 mm, 710 mm and the mass cylinder of the press D6248 with 6300 tons. See TOR and accompanying documentation (Complex service)
OKPD2 category:
Show all (1 more)
28.41.33.130 Прессы гидравлические
28.41.33.190 Прессы для обработки металлов, не включенные в другие группировки
28.91.11.144 Машины для литья под давлением
71.12.17 Услуги по инженерно-техническому проектированию производственных процессов и производств
Not applicable. Proposal shall cover the entire lot.
Restriction on submission of a bid higher than previously submitted
Bidding initiator has set a restriction on submission of a bid with a price which is higher than the price of the previous bid submitted by the bidder. Once the bid is submitted, the stated price can not be increased.
:
Yes
Upload of bid-related documents required
Bids not supported with documentation will not be considered.
:
Yes
Auto-extension
If within the last 30 minutes of bid submission period a new bid is submitted, then bid submission deadline will automatically be extended by 30 minutes from the time the last bid is submitted.
:
30 minutes
Payment terms:
100% upon delivery of the product to the Customer's warehouse.
Delivery terms:
1. Application of JSC "EPM-NEZ", Novo Cherkassk
2. Place of manufacture:
Territory of the Contractor.
3. Purpose of manufacturing:
Restore the seats of the mouthpieces and the mass cylinder in order to seal the mouthpiece-mass cylinder connection (excluding the extrusion of the electrode mass at the joint), increase the vacuum depth in the press.
4. Deadline
4.1. The contractor indicates the term of the work in the commercial proposal.
5. Brief technical description:
Mouthpieces are a replaceable tool for forming an electrode. The mass cylinder is a part of the press where the electrode mass is compressed. The mouthpiece and the mass cylinder are sealed with each other along a 15 degree cone.
6. List and scope of work performed.
6.1. Modify the mass cylinder drawing No. 28-401 according to drawing No. НС13901СБ, namely:
• prepare and weld a ring with a groove for a seal, view D drawing No. НС13901СБ, modifying the end face of the mass cylinder for installing the ring.
• bore two grooves from a diameter of 2080 mm to a diameter of 2074 mm and expand one from 65 mm to 90 mm according to drawing No. НС13901.01
• deepen 90 grooves from 22 mm to 24 mm
• restore the footprint at 15 degrees
6.2 Perform revision on a mouthpiece with a diameter of 450 mm drawing No. РМ13892, namely:
• make a groove for the seal type A
• restore the seat 15 degrees
6.3 Make revision on a mouthpiece with a diameter of 500 mm drawing No. PM13891, namely:
• make a groove for the seal type A
• restore the seat 15 degrees
6.4 Perform revision on the 555 mm diameter mouthpiece drawing No. РМ13888, namely:
• make a groove for the seal type A
• restore the seat 15 degrees
6.5 Make revision on the mouthpiece with a diameter of 610 mm drawing No. РМ13889, namely:
• make a groove for the seal type A
• restore the seat 15 degrees
6.6 Perform revision on the mouthpiece with a diameter of 650 mm drawing No. РМ13895, namely:
• make a groove for the seal type B
• restore the seat 15 degrees
6.7 Perform revision on the 710 mm diameter mouthpiece drawing No. РМ13890, namely:
• make a groove for the seal type A
• restore the seat 15 ̊.
6.8 Mouthpieces will be developed sequentially i.e. The finalized mouthpiece will be sent to the contractor, after its finalization, it will be returned to the customer, and only after that the next mouthpiece will be taken for revision.
6.7 Reconstruction of the 15 degree seat consists in recessing the cone surface by 4 mm (per side), followed by surfacing and final machining to obtain dimensions according to the drawing. 7. Requirement for TCH:
The contractor in his commercial proposal indicates the deadlines, cost (for each of clauses 6.1 - 6.7 and in total, transportation costs, payment options for work and other conditions.
8. Terms of payment:
100% upon delivery of the Products to the Customer's warehouse.
9. Acceptance of the Product is carried out on the territory of the Customer with the signing of the Acceptance Certificate.
10. The Contractor provides the Customer with a warranty for the product for at least 12 months from the date of commissioning.
11. Requirements for the Contractor
11.1. The contractor must have the necessary production and human resources to carry out this work
11.2. Employees involved in the performance of work must have professional training appropriate to the nature of the work.
Georeferencing:
Rostov region, Novocherkassk, Aluminum platform
Comments: The participant who took part in the procedure (made an offer), before the deadline for accepting applications, must upload the following documents to the system:
1. Charter (with all additions and changes, if any).
2. Certificate of state registration.
3. Tax registration certificate.
4. Extract from the Unified State Register of Legal Entities.
5. Balance sheet as of the last reporting date with the tax authority's mark of acceptance.
6. Documents confirming the authority of the representative to sign documents:
- Decision (Protocol).
- Power of attorney.
7. Work proposal (see the file "Work proposal")
8. Contact person: Martyschenko Oleg Mikhailovich - Chief Mechanic. Tel. 8 (8635) 29-48-24, fax 8 (8635) 29-42-55, e-mail: OMartischenko@energoprom.ru
9. Certificate of compliance with the requirements of ISO 9001: 2008 (if available)
This request is not a notice of a tender or auction and does not give any rights to participants, does not entail the emergence of any obligations other than those expressly indicated in the notice.
10. Before issuing a work permit for work, the Contractor is obliged to provide the Customer with the following documents:
- copy of the certificate (SRO) for the right to perform this type of work;
- copies of documents confirming the presence of a labor protection service and / or a labor protection specialist in a contractor (order for appointment to a position in a contractor, a certificate of a labor protection specialist) or the existence of an agreement with an accredited organization in the field of labor protection services;
- a copy of the instruction on labor protection from the instruction log;
- POR or PPR or RTI;
- copy of the protocol of certification of workers for labor protection;
- copies of certificates of attestation of engineers and technicians for labor protection and general industrial safety requirements. When performing work on gas, on vessels operating under pressure, using PMG, in electrical installations, during hot work - copies of certificates for each type of work;
- medical clearance of personnel;
- copies of certificates of gas-electric welders, slingers, crane drivers, hoists (towers). For gas-electric welders, copies of the certification protocols for PTM.
In case of revealing inconsistencies of the information in the submitted documents with the requirements of regulatory legal acts, the Customer has the right to initiate an audit by the Health and Safety Service in matters of Labor Protection and Industrial Safety in the Contractor's organization.
Venue of bidding:
This call for bids is held in electronic form on the e-marketplace of B2B-Center group (www.b2b-center.ru). Bids shall be submitted in the form of e-document.
Контактное лицо:
Мартыщенко Олег Михайлович - Главный механик. Тел. 8 (8635)29-48-24, факс 8 (8635)29-42-55, e-mail: OMartischenko@energoprom.ru
