Refinement of mouthpieces 450 mm, 500 mm, 555 mm, 610 mm, 650 mm, 710 mm and mass cylinder press D6248 us.6300 tn See TK and accompanying documentation (Complex service)
OKPD2 category:
Show all (1 more)
28.41.33.130 Прессы гидравлические
28.41.33.190 Прессы для обработки металлов, не включенные в другие группировки
28.91.11.144 Машины для литья под давлением
71.12.17 Услуги по инженерно-техническому проектированию производственных процессов и производств
Not applicable. Proposal shall cover the entire lot.
Restriction on submission of a bid higher than previously submitted
Bidding initiator has set a restriction on submission of a bid with a price which is higher than the price of the previous bid submitted by the bidder. Once the bid is submitted, the stated price can not be increased.
:
Yes
Upload of bid-related documents required
Bids not supported with documentation will not be considered.
:
Yes
Auto-extension
If within the last 30 minutes of bid submission period a new bid is submitted, then bid submission deadline will automatically be extended by 30 minutes from the time the last bid is submitted.
:
30 minutes
Payment terms:
100% on the actual delivery of the product to Customer's warehouse.
Delivery terms:
1. Application of EPM-NEZ JSC, g. Novo cherkassk
2. Place of manufacture:
Executor's territory.
3. Purpose of manufacture:
Restore mouthpiece and mass cylinder seats to seal the mouthpiece and mass cylinder connection (excludes electrode mass extrusion at joint joint), increase depth vacuum in the press.
4. Work Deadline
4.1. The execution date is indicated by the executor in the commercial offer.
5. Short datasheet:
Mouthpieces are a replaceable tool for electrode formation. The mass cylinder is the part of the press where the electrode mass compression process goes. The mouthpiece and mass cylinder are compacted between each other at a 15-degree cone.
6. List and scope of work carried out.
6.1. Refinalize the mass cylinder drawing No. 28-401 according to drawing No. NC13901SB, namely:
• prepare and weld the ring with seal seal type G drawing No. NC13901SB, refining the mass cylinder turner for the ring installation.
• bend two grooves from 2080 mm to 2074 mm diameter and one expand from 65 mm to 90 mm according to drawing no. NS13901.01
• deepen 90 groove from 22 mm to 24mm
• restore the 15 degree seat
6.2. Refinalize the 450 mm mouthpiece drawing No. RM13892, namely:
• manufacture groove for seal type A
• restore the 15 degree seat
6.3. Refinalize the 500 mm mouthpiece drawing No. RM13891, namely:
• manufacture groove for seal type A
• restore the 15 degree seat
6.4. Refinalize the 555 mm mouthpiece drawing No. RM13888, namely:
• manufacture groove for seal type A
• restore the 15 degree seat
6.5. Refinalize the 610 mm mouthpiece drawing No. RM13889, namely:
• manufacture groove for seal type A
• restore the 15 degree seat
6.6. Refinalize the 650 mm mouthpiece drawing No. RM13895, namely:
• manufacture groove for seal type B
• restore the 15 degree seat
6.7. Refinalize the 710 mm mouthpiece drawing No. RM13890, namely:
• manufacture groove for seal type A
• Restore the seat 15.
6.8 The mouthpieces will be finalized sequentially, i.e., the refined mouthpiece will be sent to the contractor, returned to the customer after it is finalized and only after that will be picked up the next mouthpiece to be finalized.
6.7 Restoration of the 15 degree seat is to run the cone surface 4 mm (per side) followed by surfacing and final machining to obtain dimensions according to the drawing 7. TCP Requirement:
The Contractor, in his business offer, specifies the timing of performance, cost (for each of items 6.1 to 6.7 and cumulative, transportation costs, payment options, and other terms and conditions.
8. Payment Terms:
100% on the product delivery to the Customer's warehouse.
9. The product is taken in the Customer's territory with the signing of the Accession Act.
10. The Contractor provides the Customer with a warranty for the product at least 12 months from the date of commissioning.
11. Performer Requirements
11.1. The executor must have the necessary production and human resources to carry out this work
11.2. Employees engaged to perform the work must have training appropriate to the nature of the work.
Georeferencing:
Rostov region, Novocherkassk, Aluminum platform
Comments: The participant who has taken part in the procedure (making an offer) is required to upload the following documents to the system before the deadline for the application deadline:
1. Charter (with all additions and modifications if there were any).
2. Certificate of State Registration.
3. Tax Accounting Certificate.
4. Extract from EGRUL.
5. The balance sheet as of the latest reporting date with the tax authority's acceptance mark.
6. Documents confirming the representative's signature credentials:
— Decision (Protocol).
— Power of attorney.
7. Proposal for work (see Proposal file)
8. Contact person: Oleg Martyshchenko - Chief Mechanic. Tel 8 (8635) 29-48-24, fax 8 (8635) 29-42-55, e-mail: OMartischenko@energoprom.ru
9. ISO 9001:2008 Certificate of Compliance (if available)
This request is not a notice of a contest or auction and does not give any rights to the participants, and does not entail any duty other than expressly specified in the notice.
10. The Contractor is required to provide the following documents to the Customer prior to the clearance of the work permit:
- a copy of the certificate (SRO) for the right to perform this type of work;
- copies of documents confirming a occupational health service and/or occupational health professional (contract appointment order, certificate occupational health professional) or having a contract with an accredited organization in the field of occupational health services;
- a copy of the occupational health briefing from the briefing log;
- ERP or PPR or RTI;
- a copy of the Occupational Safety Workers' Certification Protocol;
- copies of ITR certification certificates for occupational health and general industrial safety requirements. When performing gas, pressure receptacles, GPM, electrical installations, fire, copies of the certificates for each type of work;
- staff medical clearance;
- copies of the certificates of gas welders, rafers, cranes machinists, hoists (towers). For electric gas welders, copies of PTM certification protocols.
In case of discrepancies in the submitted documents, the Customer is entitled to initiate an audit by the OT and PB in occupational safety matters and Industrial safety in the Contractor organization.
Venue of bidding:
This call for bids is held in electronic form on the e-marketplace of B2B-Center group (www.b2b-center.ru). Bids shall be submitted in the form of e-document.
Контактное лицо:
Мартыщенко Олег Михайлович - Главный механик. Тел. 8 (8635)29-48-24, факс 8 (8635)29-42-55, e-mail: OMartischenko@energoprom.ru
The Organizer has announced the results on 28.07.2021 at 09:55
and selected the winner: \"IMZ \"Molot\" OOO – (Bidder 2) (Марков А.В.) submitting a bid dated of 16.07.2021 10:29 totalling to 9 583 610,83 RUB (price excl. of VAT)
