Design of heating individual heat unit for heating of electrode and nipple blanks in heating well 1 of the Peco Propip Vertical Autoclaves See the technical assignment and related documentation (Complex service)Collapse
OKPD2 category:
Show all (1 more)
27.51.26.110 Приборы отопительные электрические
29.32.30.260 Системы вентиляции, отопления и кондиционирования воздуха, их узлы и детали
29.32.30.269 Узлы и детали систем вентиляции, отопления и кондиционирования воздуха, не включенные в другие группировки
41.10.10.000 Документация проектная для строительства
Not applicable. Proposal shall cover the entire lot.
Restriction on submission of a bid higher than previously submitted
Bidding initiator has set a restriction on submission of a bid with a price which is higher than the price of the previous bid submitted by the bidder. Once the bid is submitted, the stated price can not be increased.
:
Yes
Upload of bid-related documents required
Bids not supported with documentation will not be considered.
:
Yes
Auto-extension
If within the last 30 minutes of bid submission period a new bid is submitted, then bid submission deadline will automatically be extended by 30 minutes from the time the last bid is submitted.
:
30 minutes
Payment terms:
In a Commercial Offer
Delivery terms:
1. Application of EPM-NEZ JSC, g. Novocherkassk
2. Purpose of the work:
2.1. Perform a thermal unit project to heat the blanks in the heating well No. 1 of the impregation section with vertical autoclaves of the ZPOIP.
2.2. Optimize and improve the existing heating system for workpieces in heating well No.1.
2.3. The system must include instruments and devices to automatically control the heating process of the workpieces, as well as appliances and safety devices that prevent heating accidents.
3. Project Description
3.1. Heating well No.1 is used to heat electrode and nipple blanks before impregnating them in a vertical autoclave.
3.2. Natural gas combustion products are used as a coolant.
3.3. The current workpiece heating scheme uses a horizontal cylindrical fireproof brick-lined fireproof firewall with gas shutter system, powered by natural gas and used for heating two heating wells.
Existing heating scheme.
3.4. The following results are to be obtained from the design:
- In order to heat the workpieces in heating well No.2, an individual heat unit must be selected to ensure the heating of the workpieces in the medium temperature interval in well 320-350°C;
- Time to reach the required temperature in the heating well not more than 2 hours;
- a process control and control system should be developed to reduce the role of human factors, as well as ensure safety in the operation of the equipment.
4. Composition of equipment used.
4.1. Heating well No.1.
4.2. The type is mine.
4.2.1. The heating well is designed to preheat the workpieces.
4.2.2. One time loading 30000 kg.
4.2.3. The heating temperature of the workpieces (320-350) 0C for heating wells #1; 2; (340+10/-20) 0C for heating well No.3.
4.2.4. Heating and unloading time of workpieces: 10 to 16 hours, depending on the type, size of workpieces, and equipment used.
5. Requirements for workpiece heating control and burner automation.
5.1. The workpiece heating control system shall control the lifting and temperature extraction of the heating well automatically and manually according to the process process.
5.2 The system shall display process and technical parameters of the process.
5.3 The system must allow it to be connected via a factory network and transmit data over OPC.
5.4 The automated gas burner shall comply with the requirements of Customs Union Technical Regulations TR/TC 016/2011 and be controlled both from the workpiece heating system and c local control unit.
6. List of basic data and requirements.
List of key data and requirements
1. Production volumes and time periods 1.1. Development of project (P) and working (P) documentation according to the calendar plan.
1.2. Author supervision during installation
1.3 The expert organization's opinion on the project documentation on business security registered in Rostekhnadzor.
2. Key technical solutions 2.1. The piping point is an 80mm diameter gas pipeline at the entrance to the shop. Gas pressure at the discharge point is 0.8kg/cm2. Refine the point of the point in place.
2.2. Provide GRPS-1pc installation.
2.3. Provide a CTZ installation and gas control system.
2.3. Considerate the gas flow rate.
2.5. Gas pressure up to GRPSH 0.8kg/cm2, gas pressure after GRPSH according to heat generator passport.
3. Special Conditions 3.1. The customer provides construction and process documentation for the shop and drawings of existing gas pipelines and engineering communications in the shop.
3.2. Estimated documentation at 2000 and current prices.
3.3. After undergoing the examination, transmits the corrected project in 4 exs. and working drawings in 4 ex. and 1 ex. electronically.
7. Timing of the work.
The timing of the work is specified by the Parties further at the conclusion of the contract
8. Admissions.
The design work is considered to be fully completed following the signing of the Project Documentation Acceptance Act by Parties.
• The executor presents the design in three copies on paper and one, CAD format (for drawings) and DOC (for documentation) on electronic media.
9. Performer Requirements
9.1. The performer must have the necessary production and human resources to carry out the work and be a member of a self-regulatory organization (SRO).
9.2. In order to clarify the conditions of performance, familiarization of the object must be made available to the Contractor's representatives to the Customer
3.3 The Contractor specifies the payment procedure and other terms and conditions in his business offer.
Comments: The participant who has taken part in the procedure (making an offer) is required to upload the following documents to the system before the deadline for the application deadline:
1. Charter (with all additions and modifications if there were any).
2. Certificate of State Registration.
3. Tax Accounting Certificate.
4. Extract from EGRUL.
5. The balance sheet as of the latest reporting date with the tax authority's acceptance mark.
6. Documents confirming the representative's signature credentials:
— Decision (Protocol).
— Power of attorney.
7. Proposal for work (see Proposal file)
8. Contact persons:
Leading Energy Engineer — Vorotyntsev Alexander Nikolaevich Tel 8 (8635) 29-44-32 AVorotyncev@energoprom.ru
9. ISO 9001:2008 Certificate of Compliance (if available)
This request is not a notice of a contest or auction and does not give any rights to the participants, and does not entail any duty other than expressly specified in the notice.
10. Performer Requirements:
— Permissive documents (SRO, licenses, tolerances)
— Development by the PPR, PRC, RTI.
— Certification of supervisor, ITR, industrial safety workers at the GOPO.
— Medical admission of staff to work at GOPO.
—The Contractor must provide the Customer with the following documents before the work permit is issued: copies of documents confirming the presence of the occupational health service and/ or occupational health professional (contracting order, occupational safety certificate) or having a contract with an accredited organization in the field of delivery health services.
A commercial offer is REQUIRED to consider the application.
Venue of bidding:
This call for bids is held in electronic form on the e-marketplace of B2B-Center group (www.b2b-center.ru). Bids shall be submitted in the form of e-document.
