Restoring the usability of building roofs
ЦО 2 inventory number 2665, ЦОЭЭП inventory number 1626, СПЦ 2 Crushing and grinding department inventory number 1370, CPOiP inventory number 2671, CGE section number 2 inventory number 1121, KP-8...
Restoring the usability of building roofs
ЦО 2 inventory number 2665, ЦОЭЭП inventory number 1626, СПЦ 2 Crushing and grinding department inventory number 1370, CPOiP inventory number 2671, CGE section number 2 inventory number 1121, KP-8 inventory number. No. 3189, the building of the KRP garage inventory number 4288, Locomotive depot inventory number 2911, SPTs 1 Grinding department inventory number 2353, SPTs 1 Extended calcination department (rotary kilns) inventory number 2357, SPTs 1 Calcination department (retort furnaces) inventory .№ 2352. See terms of reference (Complex service)Collapse
OKPD2 category:
Show all (8 more)
25.11.23.119 Конструкции и детали конструкций из черных металлов прочие, не включенные в другие группировки
25.93.13.112 Решетки, сетки и ограждения из проволоки из черных металлов
25.93.13.122 Решетки, сетки и ограждения из проволоки из меди
25.99.99.000 Услуги по производству прочих металлических изделий, не включенных в другие группировки, отдельные, выполняемые субподрядчиком
43.91.19.110 Работы строительные по устройству любых видов кровельных покрытий зданий и сооружений
43.91.19.120 Работы строительные по монтажу водосточных желобов, труб, кровельных сливов, а также по устройству плиточных и металлических сливов
43.91.19.190 Работы кровельные прочие, не включенные в другие группировки
43.99.10.120 Работы по гидроизоляции наружных конструкций зданий и сооружений и прочих подземных сооружений
43.99.90.190 Работы строительные специализированные прочие, не включенные в другие группировки
25.99.99.222 Услуги по изготовлению сшивно-кровельного покрытия из железа по индивидуальному заказу населения
25.99.99.229 Услуги по изготовлению прочих металлических предметов хозяйственного назначения по индивидуальному заказу населения
Not applicable. Proposal shall cover the entire lot.
Restriction on submission of a bid higher than previously submitted
Bidding initiator has set a restriction on submission of a bid with a price which is higher than the price of the previous bid submitted by the bidder. Once the bid is submitted, the stated price can not be increased.
:
Yes
Upload of bid-related documents required
Bids not supported with documentation will not be considered.
:
Yes
Auto-extension
If within the last 30 minutes of bid submission period a new bid is submitted, then bid submission deadline will automatically be extended by 30 minutes from the time the last bid is submitted.
:
30 minutes
Payment terms:
In a commercial offer
Delivery terms:
1. Application of EPM-NEZ JSC, Novocherkassk
2. The purpose of the work.
2.1. Restoring the serviceability of the roofs of buildings ЦО 2 inv.№ 2665, ЦМОЭП inv.№ 1626, СПЦ 2 Crushing and grinding department inv.No. 1370, TsPOiP inv.No. 2671, TsGE section # 2 inv.No 1121, KP-8 inv. No. 3189, the building of the KRP garage inventory number 4288, Locomotive depot inventory number 2911, SPTs 1 Grinding department inventory number 2353, SPTs 1 Extended calcination department (rotary kilns) inventory number 2357, SPTs 1 Calcination department (retort furnaces) inventory .№ 2352.
3. The list and volume of work performed.
3.1.
№№ Description of works and defects Unit of measure Quantity
Roasting shop No. 2 inv.№ 2665 ЦО 2 inv.№ 266
1. Dismantling of steel sheet castings δ = 0.55 mm tn 0.922
2. Rust removal of existing sheet steel castings 100 m2 1.76
3. Primer of existing tides, on the one hand, at a time 100 m2 1.76
4. Painting of metal structures of existing castings for two times 100 m2 1.76
5. Dismantling of soft roll roofing of adjacencies, in some places up to 0.6 m 100 m2 1.26
6. Dismantling of surfaced materials 100m2 of coating 3.96
7. Dismantling the leveling cement-sand screed 15 mm thick 100m2 screed 2.86
8. Add screed disassembly from 15mm to 30mm 100m2 screed 2.86
9. The installation of cement screed in individual places δ = 30 mm 100m2 screed 2.86
10. The device is a soft roll roof of deposited materials in one layer. 100 m2 10.20
11. Primed substrates with finished bitumen emulsions 100 m2 18.63
12. The device of a soft rolled roof from deposited materials in two layers. 100 m2 15.16
13. The device of adjacencies of three-layer of deposited materials up to 0.6 m high. without an apron. 100 m / s 5.78
14. Production of steel castings δ = 0.55 mm tn 0.085
15. Primer of existing tides on both sides at a time 100 m2 0.384
16. Painting of metal structures of existing castings for two times 100 m2 0.384
17. Installation of steel castings δ = 0.55 mm 100 m2 0.192
18. The device is a soft roll roof lantern from deposited materials in one layer. 100 m2 22.45
19. Repair of a windbreak made of slate m2 27
20. Dismantling of the technological pipeline tn 6.4
21. Cleaning construction waste t. 43
22. Sorting construction waste. tons 43
23. Loading construction waste onto vehicles in a mechanized way. tons 43
24. Loading and cutting scrap metal tn 7.6
CMOEP inv.No 1626
1. Dismantling of steel sheet castings δ = 0.55 mm tn 0.086
2. Production of steel castings δ = 0.55 mm tn 0.086
3. Priming of ebbs from two sides at a time 100 m2 0.023
4. Painting of the metal structures of the ebb twice for 100 m2 0.023
5. Dismantling of soft roll roofing of adjacencies, in some places up to 1 m 100 m2 1.26
6. Dismantling of surfaced materials 100m2 of coating 1.67
7. Dismantling the leveling cement-sand screed 15 mm thick 100m2 screed 1.20
8. Add screed disassembly from 15mm to 30mm 100m2 screed 1.2
9. The device of cement screed in individual places δ = 30 mm 100m2 screed 1.2
10. The device is a soft roll roof of deposited materials in one layer. 100 m2 6.93
11. Primed substrates with finished bitumen emulsions 100 m2 3.61
12. The device of a soft rolled roof from deposited materials in two layers. 100 m2 1.67
13. The device of adjacencies of three-layer of deposited materials up to 1 m high. without an apron. 100 m / p 1.94
17 Installation of steel castings δ = 0.55 mm 100 m2 0.192
18 The device is a soft roll roof lantern of deposited materials in one layer. 100 m2 1.2
19 Dismantling roof funnels pcs 6
20 Installation of roof funnels pcs 6
20 Construction waste cleaning tn. 18.7
21 Sorting construction waste. tons 18.7
22 Loading of construction waste onto vehicles in a mechanized way. tons 18.7
23 Loading and cutting of scrap metal tn 0.15
TWS 2 Crushing and grinding department Inv.No 1370
1. Dismantling of parapet plates (0.4 * 0.74) pcs 188
2. Plastering the surface of the parapet wall m2 70
3. Primed substrates with finished bitumen emulsions 100 m2 1.32
5. The device of adjacencies in one layer of deposited materials up to 0.6 m high without an apron. 100 m / p 1.55
6. Production of steel castings δ = 0.55 mm tn 0.423
7. Priming of ebbs from two sides at a time 100 m2 0.98
8. The color of the metal structures of the ebbs for two times 100 m2 0.98
9. Installation of steel castings δ = 0.55 mm 100 m2 0.98
10. Repair of the roof overlay coating in separate places in 1 layer 100 m2 0.5
11. Cleaning construction waste t. 12.7
12. Sorting of construction waste. tons 12.7
13. Loading construction waste onto motor vehicles in a mechanized way. tons 12.7
TsPOiP inv.№ 2671
1. Repair of adjoining the roof to the wall up to 0.6 m. Without an apron mp 29
2. Repair of roof overlay coating in separate places in 2 layers 100 m2 2.24
3. Dismantling of sheet steel castings δ = 0.55 mm tn 0.421
4. Rust removal of existing sheet steel castings 100 m2 0.98
5. Primer of existing tides, on the one hand, at a time 100 m2 0.98
6. Painting of the metal structures of the existing ebbs for two times 100 m2 0.98
7. Installation of steel castings δ = 0.55 mm 100 m2 0.98
8. Dismantling of soft roll roofing of adjacencies, in some places up to 0.6 m 100 m / p 1.35
9. The device screed of cement mortar on the abutment of the roof to the wall. 100 m2 0.79
10. Primed substrates with finished bitumen emulsions 100 m2 3.65
11. The device of adjacencies of three-layer of deposited materials up to 0.6 m high. without an apron. 100 m / p 1.35
12. Production of steel castings δ = 0.55 mm tn 0.027
13. Priming of ebbs on both sides at a time 100 m2 0.006
14. Painting of metal structures of the ebbs twice per 100 m2 0.006
15. Device for wind protection of lanterns from lumber in = 40mm 1m³ 0.196
16. The device is a soft roll roof lantern from deposited materials in one layer. 100 m2 0.82
17. Cleaning construction waste t. 11.8
18. Sorting construction waste. tons 11.8
19. Loading construction waste onto vehicles in a mechanized way. tons 11.8
TsGE section No. 2 inv.№ 1121
1. Installation of steel castings δ = 0.55 mm 100 m2 0.16
2. Repair of the roof overlay coating in separate places in 2 layers of 100 m2 1.42
3. Dismantling of soft roll roofing of adjacencies, in some places up to 1 m with an apron of 100 m / p 0.84
4. The device of adjacencies of three-layer of deposited materials up to 1 m high. with an apron 100 m / p 0.84
5. Brickwork m³ 0.3
Cleaning construction waste t. 4.2
Loading construction waste onto vehicles in a mechanized way. tons 4.2
KP-8 inv. No. 3189
1. Dismantling of a soft rolled roof of M2 1,8
2. Dismantling of soft roll roofing of adjacencies, up to 0.6 m 100 m / p 0.22
3. Dismantling of steel sheet castings δ = 0.55 mm tn 0.134
4. Production of steel castings δ = 0.55 mm tn 0.134
5. Priming of ebbs on both sides at a time 100 m2 0.62
6. Painting of the metal structures of the ebbs at two times 100 m2 0.62
7. Installation of steel castings δ = 0.55 mm 100 m2 0.31
8. The device is a soft roll roof of deposited materials in three layers. 100 m2 1.8
9. The device of adjacencies of three-layer of deposited materials up to 0.6 m high. 100 m / p 0.22
10. Cement screed repair 100 m2 0.25
11. Primed substrates with finished bitumen emulsions 100 m2 1.98
12. Cleaning construction waste t. 2,8
13. Sorting construction waste. tons 2,8
14. Loading construction waste onto vehicles in a mechanized way. tons 2,8
15. Loading and cutting scrap metal tn 0.134
The building of the KRP garage inv.№ 4288
1. Dismantling a soft roll roof 100 m2 2.56
2. Dismantling of a soft rolled roof of adjacencies with an apron, to 0,6 m 100 m / p 0,26
3. The device is a soft roll roof of deposited materials in three layers. 100 m2 2.56
4. The device of adjacencies of three-layer of deposited materials up to 0.6 m high with an apron. 100 m / p 0.26
5. Cement screed repair 100 m2 0.49
6. Primed substrates with finished bitumen emulsions 100 m2 2.76
7. Production of steel castings δ = 0.55 mm tn 0.088
8. Priming of ebbs on both sides at a time 100 m2 0.24
9. Painting of metal structures of the ebb twice for 100 m2 0.24
10. Cleaning construction waste t. 2.7
11. Sorting construction waste. tons 2.7
12. Loading construction waste onto vehicles in a mechanized way. tons 2.7
Engine depot Inv.No 2911
1. Dismantling soft roll roofing 100 m2 0.72
2. Dismantling of a soft rolled roof of adjacencies up to 0.6 m 100 m / p 0.14
3. Dismantling of sheet steel castings δ = 0.55 mm tn 0.045
4. Production of steel castings δ = 0.55 mm tn 0.045
5. Priming of ebbs from two sides at a time 100 m2 0.20
6. Painting of the metal structures of the ebbs twice per 100 m2 0.20
7. Installation of steel castings δ = 0.55 mm 100 m2 0.20
8. The device is a soft roll roof of deposited materials in three layers. 100 m2 0.72
9. The device of adjacencies of three-layer of deposited materials up to 0.6 m high with an apron. 100 m / p 0.14
10. Cement screed repair 100 m2 0.19
11. Primed substrates with finished bitumen emulsions 100 m2 0.84
12. Cleaning construction waste t. 1.9
13. Sorting construction waste. tons 1.9
14. Loading construction waste onto vehicles in a mechanized way. tons 1.9
15. Loading and cutting scrap metal tn 0.045
SEC №1 Grinding department inv.№ 2353
1. Dismantling of parapet ebbs tn 0.12
2. Production of steel castings δ = 0.55 mm tn 0.608
3. Priming of ebbs on both sides at a time 100 m2 2.82
4. Painting of the metal structures of the ebbs for two times 100 m2 2.82
5. Installation of steel castings δ = 0.55 mm 100 m2 1.41
6. Repair of roof overlay coating in separate places in 2 layers 100 m2 0.7
7. Cleaning construction waste t. 3,5
8. Loading construction waste onto vehicles in a mechanized way. tons 3,5
9. Loading and cutting scrap metal tn 0.12
SPTs1 Extended calcination department (rotary kilns) inventory number 2357
SOC 1 Calcination department (retort furnaces) inventory number 2352.
1. Repair of roof overlay coating in separate places in 2 layers 100 m2 3.5
2. Primed substrates with finished bitumen emulsions 100 m2 3.5
3. Cleaning construction waste t. 4,5
4. Loading construction waste onto vehicles in a mechanized way. tons 4,5
Note: The costs of installation, dismantling of temporary sites, installation, removal of winches, rigging, devices for lifting material, the contractor must consider in accordance with the developed PPR. These volumes are not included in the list of volumes of work by the customer.
5. Materials, mechanisms, equipment and tools provided by the Contractor.
5.1. Work is performed from customer’s material
5.2. Lifting mechanisms and mechanisms for loading and installation works are provided by the contractor.
5.3. Electric welding and gas cutting equipment, power tools, oxygen, propane, auxiliary materials are provided by the contractor.
6. Requirements for the Contractor.
6.1. The contractor must have the necessary production and human resources to carry out this work, be a member of a self-regulatory organization (SRO).
6.2. To clarify the conditions for the performance of work, familiarization with the object, it is desirable that the representatives of the Contractor arrive at the Customer.
6.3. The contractor in his proposal indicates the payment procedure and other conditions.
6.4. Certification of the head, engineering and industrial safety and labor protection performers at the public educational institution. According to Appendix No. 1.
6.5. Ensuring HSE measures with safe methods for performing work at the facility.
6.6. The contractor is obliged to provide copies of documents confirming the presence of a labor protection service and / or labor protection specialist in the contractor (order of appointment to the contractor, certificate of labor protection specialist) or an agreement with an accredited organization in the field of services labor protection.
6.7. The contractor before the start of work provides a schedule of work.
6.8. The contractor monitors the volume of exported construction waste and scrap metal by weight.
6.9. The Contractor draws up and submits to the customer the executive documentation in accordance with RD-11-02-2006. The requirements for the composition and procedure for maintaining executive documentation during the construction, reconstruction, overhaul of capital construction facilities and the requirements for certificates of survey of works, structures, sections of engineering networks technical support.
6.10. The contractor provides a local estimate.
7. Terms of work
7.1. Work at an existing enterprise in the technological windows provided, depending on the loading of equipment.
. 6.2 Development of PPR or PPRK is carried out by the Contractor.
6.3 Lifting mechanisms, lifting devices in accordance with PPR for installation are provided by the Contractor.
6.4. Vehicles for transportation of materials to the facility from warehouses, as well as scrap metal, are provided by the Contractor
8. Turnaround time.
8.1. Start of work - July2020
8.2. Completion of work - November 2020
9. A list of documents required for the execution of orders - tolerances at the enterprise is attached to the terms of reference. Annex 1
Comments: Participant who has submitted a bid before bids submission deadline shall upload the following documents:
1. Articles of Association (with all the amendments, if any).
2. Certificate of the state registration.
3. Certificate of tax registration.
4. Extract from USRLE.
5. Balance sheet as of the last reporting date with tax authority stamp of acceptance.
6. Documents confirming the powers of the person authorized to sign the documents:
— Decision (Protocol).
— Power of attorney.
7. Proposal for work (see file "Proposal for work")
8. Contact person: Tetslav Vladimir Edvinovich - Head
OEiNZIS, phone 8 86 532-9-42-13, fax 8 86352 9-46-18 e-mail: VTetslov@energoprom.ru.
9. Certificate of compliance with the requirements of ISO 9001: 2008 (if available)
This request does not constitute a notification of tender or auction and shall not grant any rights to the participants and shall not entail any obligations except those explicitly stated in the announcement.
10. Requirements for the Contractor:
- Permitting documents (SRO, licenses, admissions).
- Development by the executor of PPR, PPRK, RTI.
- Availability of certification of the head, engineers, industrial safety workers at the public educational institution.
- The presence of medical admission of personnel to work at the public educational institution.
Venue of bidding:
This call for bids is held in electronic form on the e-marketplace of B2B-Center group (www.b2b-center.ru). Bids shall be submitted in the form of e-document.
