Type: Request for Proposals

Corrugated sheet H10.40-0.7 mm Length = 2.5 m GOST 24045-2016

Type: Request for Proposals

E-competitive bidding process "Tariffer for Managing the Operation of the vehicle "Perekrestok"

Type: Request for Proposals

1. The KVO MVP-1 chain • Material for manufacturing according to GOST 4543-2016,19281-2014; • Quantity – 50m; • Drawing: W6824APR; It is used to transfer the mechanical power of mechanisms. A reliable means of power transmission with high efficiency. The assembled chain should have easy mobility of hinged joints. 2. Lamellas KVO MVP-1 • Material for the manufacture of St3; • Quantity – 130pcs; • Drawing: MVP162-00.00; The parts on the conveyor are subject to rapid wear due to the aggressive operating environment, these are temperature, friction, load. Therefore, a planned stop of the conveyor is envisaged to replace the components with new ones Cloaks of QUO, Chain of QUO

Type: Request for Proposals

Provision of maintenance services Compressor room. Consists of three compressors: Airpol PR30 2 pcs Airpol 30 1pc As a result of inspection of the Airpol PR30 P19381213 compressor, the following was revealed: 1. Strong noise of electric motor bearings. 2. Increased vibration when starting the compressor. Provision of maintenance services for the compressor Airpol PR30 P19381213.

Type: Request for Proposals

Rendering of major repair services for the Renner RS 1-30 compressor. Compressor room. Consists of three compressors: Alup Largo 30-8 2pcs Alup SCK-22 1pc Renner RS1-30 As a result of inspection of the Renner RS 1-30 compressor, the following was revealed: 1. Strong noise of the bearings of the electric motor and the screw block. 2. The axial backlash of the rotor of the screw block is beyond the manufacturer's tolerance 3. Increased vibration when starting the compressor. 4. Destruction of the rubber damper of the compressor bed. Rendering of major repair services for the Renner RS 1-30 compressor.

Type: Request for Proposals

Provision of maintenance services for Hitachi OSP55 M5ARN compressor. Compressor room. Consists of three compressors: Alup Largo 30-8 1pc Alup Solo 30 1pc Alup SCK42-8 2 pcs Hitachi OSP55 M5ARN 1pc As a result of inspection of the Hitachi OSP55 M5ARN compressor, the following was revealed: 1. Strong noise of electric motor bearings 2. The need for scheduled maintenance with replacement of oil separators. 3. Increased vibration and noise during compressor operation. 4. Destruction of the rubber damper of the compressor bed. Provision of maintenance services for Hitachi OSP55 M5ARN compressor.

Type: Request for Quotations

Mesh, corrugated sheet,barbed wire for the needs of LLC SEC Chistogorsky

Type: Request for Proposals

1. Shank 2-4 rolls: • Material for manufacture: Steel 06H12NZD • Drawing No.: CF-01.00.332; • Quantity: 40 pcs.; 2. Shank of the 1st roll • Material for manufacturing; Steel 06H12NZD • Drawing No.: TM 2298.00.000; • Quantity: 10 pcs. 3 . The Ring • Material for manufacturing Steel 40X; • Drawing No.: CF-01.00.310; • Quantity: 16 pcs. 4. Graphite-fluoroplastic seal: • Material for the manufacture of F4K20; • Drawing No.: TM 1624.00.000; • Quantity: 60 pcs 5. Support: • Material for the manufacture of LS 59-1; • Drawing No.: TM 01.00.201; • Quantity: 40 pieces Shank 2-4 rolls, Shank of the 1st roll, Graphite fluoroplastic seal, Ring, Support

Type: Request for Proposals

1. Fan shaft: • Drawing: TM 1918.00.000 • Quantity: 18 pcs. • Material for manufacturing Steel 45 Shafts (Revolutions up to 3000 rpm) are used in the fan housing – the main part of the edge trimming unit on the mineral wool plate production line. With the help of this fan, crushed mineral wool products are transported, it has a large abrasive. Fan shaft of the edge trim assembly

Type: Request for Proposals

1. Rear SKIP wheel: • Drawing: RP 12219N.1-125SB • Quantity: 2 pcs. • Material for manufacturing Steel 3, paronite H1, Steel 45 2. The wheel on the SKIP front: • Drawing: RP 12219N.1-115SB • Quantity: 2 pcs. • Material for manufacturing Steel 3,Steel 35,Sheet 18 SKIP wheel (rear,front)

Type: Request for Proposals

Roofing materials Profiled sheet, insulation, steam, wind protective membranes, fasteners

Type: Request for Quotations

Metal products for JSC Sibagro PF "Tomskaya"

Type: Request for Proposals

Supply of consumables, building materials and tools for joint venture JSC TanderMTOZ-24-296MTOZ-24-391MTOZ-24-416 See the bid documentation and Procured items for more details

Type: Request for Proposals

Purchase of LED lamps 1. LED lamp SPO-107D 36W 160-260V 6500K 2900Lm 1200mm with motion sensor IP40 ASD - 2 pcs. 2. LED lamp 595*595mm Armstrong ceiling with light sensor and motion sensor - 49 pcs.

Type: Request for Proposals

Manufacture of spline shafts for carriage travel of overhead electric cranes. 1. To make spline shafts from 40X steel grade according to the drawing 2. Perform heat treatment of the spline 47-52 HRC according to the technical documentation. Manufacture of spline shafts for carriage running of overhead electric cranes.

Type: Request for Proposals

Provision of services for conducting preliminary (when applying for a job) and periodic medical examinations. Requirements for the Contractor. 1. Availability of a license to carry out activities. 2. Confirmation of the freely available and owned (rented) equipment necessary for the provision of services. 5. The Contractor is fully responsible for the activities performed 6. The contractor is responsible for the high-quality and timely performance of services for conducting preliminary (when applying for a job) and periodic medical examinations in accordance with the requirements of Russian legislation. 7. The driver of the vehicle and accompanying persons (if necessary) must have with them an identity document (passport), a driver's license, and a vehicle registration certificate. 2. Place of work: Preliminary medical examinations – at the location of the medical organization. Periodic medical examinations: - Krasnaya Glinka, Krasnoglinskoe highway 20 - p. Volzhsky, Krasnoyarsk district, Production 1 - Alekseevka settlement, Zavodskoy proezd 1 - Samara, Zavodskaya str., 5 Provision of services for conducting preliminary (when applying for a job) and periodic medical examinations.

Type: Request for Proposals

Provision of services for commission psychiatric examinations. 1. Requirements for the Contractor. 1.1. Availability of a license to carry out activities. 1.2. Confirmation of freely available and owned (rented) equipment necessary for the provision of services. 1.3. The Contractor is fully responsible for the activities performed 1.4. The Contractor is responsible for the high-quality and timely performance of services for conducting preliminary (when applying for a job) and periodic medical examinations in accordance with the requirements of Russian legislation 2. Place of work: At the location of the medical organization in Samara. Provision of services for commission psychiatric examinations.

Type: Request for Proposals

Partial technical inspection of lifting facilities in accordance with the requirements of Rostechnadzor Order No. 461 dated 11/26/2020 "On Approval of Federal Norms and Rules in the field of industrial safety Safety Rules for Hazardous Production facilities where lifting facilities are used." It is necessary to carry out: partial technical inspection of lifting facilities – 7 units: - overhead electric double-girder crane controlled from the floor (head No. 27017, carrying capacity 10.0 tons); - overhead electric double-girder crane controlled from the floor (head No. 27016, load capacity 10.0 tons); - overhead electric double-girder crane controlled from the floor (head No. 27015, load capacity 10.0 tons); - overhead electric double-girder crane controlled from the floor (head No. 27014, load capacity 10.0 tons); - overhead electric double-girder crane controlled from the floor (head No. 27018, load capacity 10.0 tons); - overhead electric single-girder crane controlled from the floor (head No. 7686, carrying capacity 3.5 tons); - overhead electric single-girder crane controlled from the floor (head No. 8448, carrying capacity 3.5 tons). Partial technical inspection of lifting facilities in accordance with the requirements of Rostechnadzor Order No. 461 dated 11/26/2020.

Type: Request for Proposals

Provision of services for pumping, transportation and cleaning of liquid household waste (LW). 1. The volume of the tank is 12 m3. 2. The number of tanks – 5 pcs. 3. The estimated number of bids for the export of concrete products per year: 5 pieces. The customer has the right to change the number of services, in the direction of increase or decrease. 10. The bid is submitted on working days from 08:00 to 17:00 local time, with mandatory indication of the number of flights and the address of the facility by phone specified in the contract. Provision of services for pumping, transportation and cleaning of liquid household waste.